sifsealers (5)

SAME DAY CLEAN & SEAL - 1 FLOOD COAT APPLICATION - Penetrating Sealer System Buy 4 x 5L Concentrate and Save $165! FluoroSeal is a water based fluoropolymer sealer used for sealing porous surfaces including natural stone, clay and concrete surfaces. Suitable for garages, walls, entertaining areas, kitchens and wet areas, pool surrounds, patios, driveways. Dilution & Coverage FluroSeal is supplied as a high-performance concentrate, designed to be diluted with water on site. This reduces transport weight and allows you to mix only the amount required for the project. Dilution • 1 part FluroSeal concentrate : 3 parts clean water• 5L concentrate produces 20L of ready-to-use (RTU) sealer Typical Coverage Coverage varies depending on the surface porosity and texture. Refer to coverage chart. • Approx 5 m² per litre (RTU) on most concrete and masonry surfaces• 5L concentrate → 20L RTU → covers approximately 100 m² Project Example A typical 100 m² driveway, patio or paved area can usually be sealed with one 5L bottle of FluroSeal Concentrate when diluted to 20L ready-to-use product. Highly porous surfaces may require additional product. Always apply a small test area to confirm coverage before commencing the full application. Key advantages Superior oil and water repellence, providing excellent stain resistance Reduces water ingress and minimises efflorescence in mineral substrates Transparent, natural finish - does not significantly change appearance High penetration into masonry surfaces High wear resistance, UV stable, long life Fungal and algal resistance Easy to clean surfaces Substrates remain breathable Can be applied to damp or wet substrates Read the product information before application. The surface to be treated should be clean and free of all contaminants. The surface can be damp or wet, however FluoroSeal should not be applied to a surface that has pools of water. The pools should be removed using a broom or cloth prior to application. Do not apply FluoroSeal if rain is expected within 24 hours of application. Do not apply if extreme weather conditions are expected. Do not apply if surface temperatures are above 30 degC. If necessary, cool the surface with water prior to application. FluoroSeal is ready to apply and should be mixed well before use. A test prior to application must be performed to assess the suitability of the product. FluoroSeal is best applied using a low-pressure sprayer. The surface should be uniformly applied to saturation point. Do not allow pooling of sealer. Pools can be spread out using a soft bristled broom. Excess sealer must be removed before drying. Protect adjacent surfaces such as glass, metal or painted surfaces from any overspray. Full curing may take up to 24 hours. Avoid traffic for at least 24 hours. Equipment clean up can be performed with water.  

Surface Prep Concentrate SiF Surface Prep is a highly concentrated alkaline cleaner and degreaser designed for preparing concrete, stone, pavers and masonry surfaces prior to cleaning or sealing. It effectively removes oils, grease, dirt, grime and general contaminants, helping restore surface cleanliness and improve the performance of subsequent treatments. This versatile, water-based cleaner is suitable for use on a wide range of washable substrates including concrete, masonry, brick, paving, stone, tiles, tools and equipment, subject to testing. Its concentrated formula allows flexible dilution depending on the level of contamination. SiF Surface Prep can also be added to SiF Building Wash to help boost cleaning power where road grime, traffic film or oily contaminants are present. Dilution Guide Dilution will vary depending on the level of contamination and surface type. • General purpose cleaning: Dilute 1:50 with water• Lightly soiled surfaces: Dilute 1:10 with water• Heavy grease or contamination: Dilute up to 1:1 with water, allow to dwell, scrub if required, then rinse thoroughly Organic Growth Cleaning (SH Compatible) SiF Surface Prep can be used alongside sodium hypochlorite (SH) when treating surfaces affected by organic growth. Example mix:• 17.6L water• 2L SiF Surface Prep• 0.4L SH Always perform a small test area to confirm product suitability, dilution strength and surface compatibility before full application.

Non-hazardous, water based, neutral pH, environmentally friendly, maintenance cleaner for all sealed surfaces. SiF Surface Safe should be mixed well before use then can be sprayed on surface. General Purpose Cleaning: Dilute 1:50 with water Lightly soiled areas: Dilute 1:10 with water Heavily soiled areas: Dilute 1:1, allow to dwell, scrub if required then rinse off.

SAME DAY CLEAN & SEAL - 1 FLOOD COAT APPLICATION - Penetrating Sealer System SilaSeal Enhance is a ready to apply enhancer for aggregate and honed concrete and concrete pavers. Darkens mortar and enhances stone in aggregate concrete based materials Provides superior water repellence and oil repellence Reduces efflorescence High wear resistance, long life UV stable Water based Non-film forming, allows breathability Fungal and algal resistance Does not peel or blister Can be applied to a damp/wet surface Suitable on both horizontal and vertical surfaces Can be spray applied SilaSeal Enhance is a ready to apply, and enhancer for aggregate concrete and concrete pavers Read the product information before application. The surface to be treated should be clean and free of all contaminants. The surface can be damp or wet, however SilaSeal Enhance should not be applied to a surface that has pools of water. The pools should be removed using a broom or cloth prior to application. Do not apply SilaSeal Enhance if rain is expected within 24 hours of application. Do not apply if extreme weather conditions are expected. Do not apply if surface temperatures are above 30 degC. If necessary, cool the surface with water prior to application. SilaSeal Enhance is ready to apply and should be mixed well before use. A test prior to application must be performed to assess the suitability of the product. SilaSeal Enhance may be spray applied using a low-pressure sprayer. The surface should be uniformly applied to saturation point. For dense and non-textured surfaces such as honed concrete and natural stone, sealer can be sprayed, then buffed using a microfibre mop. Do not allow pooling of sealer. Pools can be spread out using a soft bristled broom. Excess sealer must be removed before drying. Protect adjacent surfaces such as glass, metal or painted surfaces from any overspray. Full curing may take up to 24 hours. Avoid traffic for at least 24 hours. Equipment clean up can be performed with water.

SAME DAY CLEAN & SEAL - 1 FLOOD COAT APPLICATION - Penetrating Sealer System Buy 4 x 5L Concentrate and Save $112! SilaSeal is a water based silane-siloxane sealer used for sealing porous reconstituted and natural stone, clay and concrete materials. Suitable for garages, walls, roofs, entertaining areas, kitchens and wet areas, pool surrounds, patios, driveways. Not recommended for use on very dense substrates. Dilution & Coverage SilaSeal is supplied as a high-performance concentrate, designed to be diluted with water on site. This reduces transport weight and allows you to mix only the amount required for the project. Dilution • 1 part SilaSeal concentrate : 3 parts clean water• 5L concentrate produces 20L of ready-to-use (RTU) sealer Typical Coverage Coverage varies depending on the surface porosity and texture. See coverage charts. • Approx 5 m² per litre (RTU) on most concrete and masonry surfaces• 5L concentrate → 20L RTU → covers approximately 100 m² Project Example A typical 100 m² driveway, patio or paved area can usually be sealed with one 5L bottle of SilaSeal Concentrate when diluted to 20L ready-to-use product. Highly porous surfaces may require additional product. Always apply a small test area to confirm coverage before commencing the full application. Key advantages Superior water repellence, providing excellent water based stain resistance Reduces water ingress and minimises efflorescence in mineral substrates Transparent, natural finish - does not significantly change appearance High penetration into masonry surfaces High wear resistance, UV stable, long life Fungal and algal resistance Easy to clean surfaces Substrates remain breathable Can be applied to damp or wet substrates Read the product information before application. The surface to be treated should be clean and free of all contaminants. The surface can be damp or wet, however SilaSeal should not be applied to a surface that has pools of water. The pools should be removed using a broom or cloth prior to application. Do not apply SilaSeal if rain is expected within 24 hours of application. Do not apply if extreme weather conditions are expected. Do not apply if surface temperatures are above 30 degC. If necessary, cool the surface with water prior to application. SilaSeal is ready to apply and should be mixed well before use. A test prior to application must be performed to assess the suitability of the product. SilaSeal is best applied using a low-pressure sprayer. The surface should be uniformly applied to saturation point. Do not allow pooling of sealer. Pools can be spread out using a soft bristled broom. Excess sealer must be removed before drying. Protect adjacent surfaces such as glass, metal or painted surfaces from any overspray. Full curing may take up to 24 hours. Avoid traffic for at least 24 hours. Equipment clean up can be performed with water.